elgaid59
عضو ذهبي
عدد المساهمات : 9627
نقاط : 36992
تاريخ التسجيل : 21/08/2007
 | | موضوع: مجموعة برامج ArcelorMittal حسب المواصفات الاوروبية السبت 11 أكتوبر - 18:47 | |
| .......... السلام عليكم ورحمة الله وبركاته
اقدم لكم هذه المجموعة من البرامج والمراجع التقنية وذلك حسب المواصفات الاوروبية
EN 1993 & EN 1994
والملحقات لهذه المواصفات(fire,seismic,resistance...)
هناك تقريبا 20 برنامج
ArcelorMittal AIFB v 5.32 : SlimFloor
Software developed for the design according to Eurocode 3 of slimfloor slabs based on Integrated Floor Beam (IFB) sections, which are composed from a split-up wide-flange section and a plate welded as bottom or top flange. It is only possible to calculate simple beams that are hinged at the two supports. It is possible to design also Slim Floor Beam (SFB) sections which are obtained from a complete wide-flange section welded to a plate as support for the slab elements.
ArcelorMittal ACoP v 1.02 : connections
Design software to analyse and verificate joint configuration and connections in steel structures. The calculation are based on the standards as described in Eurocode 3 Revised Annexe - J.
ArcelorMittal ABC version 2.15: Beams Calculator
software for the design and calculations of composite beams and non composite beams according to Eurocodes [1 to 5]. The application range is limited to statically determinate beams on two simple supports, with or without cantilevers at the ends. The composite beam is composed of a rolled section which may be partially encased in concrete, and of a reinforced concrete slab connected to the upper face of the section. Replaces PMX.
ArcelorMittal ACB+ version 2.04 : Cellular Beams
Cellular beams design program to optimise spans and usable ceiling height.
ArcelorMittal A3C version 1.0
Verification of steel members in bending and axial compression according to EN1993-1-1.
ArcelorMittal PSL version 1.02
Preliminary design of steel or composite structures according to Eurocode 3 [1] for steel structures and Eurocode 4 [2] for composite structures. No national application document is applied.
ArcelorMittal Portal version 1.0
The software was developed for the predesign of single span portal frames according to Eurocodes 3 [1].
ArcelorMittal PSL version 1.02
Preliminary design of steel or composite structures according to Eurocode 3 [1] for steel structures and Eurocode 4 [2] for composite structures. No national application document is applied.
ArcelorMittal Cobec 4 version 2.0
Composite Beams. Pre-design software for composite steel-concrete continous beams according ENV 1994-1-1.
ArcelorMittal ACP version 1.0.2
ArcelorMittal Construction Phase for composite solutions. To check the LTB behaviour of composite and/or partially encased beams during erection (Lateral Torsional Buckling during Construction).
ArcelorMittal ABC version 2.15: Beams Calculator
software for the design and calculations of composite beams and non composite beams according to Eurocodes [1 to 5]. The application range is limited to statically determinate beams on two simple supports, with or without cantilevers at the ends. The composite beam is composed of a rolled section which may be partially encased in concrete, and of a reinforced concrete slab connected to the upper face of the section.
ArcelorMittal ACD version 3.06 : Composite Column Design
software for the design of composite columns, composed of steel profiles, concrete and rebars, according to Eurocode 4 [1.1] (ENV 1994-1-1). The program considerates only Double-T profiles. The concrete section consists of an complete encasement of rectangular or circular shape or of a filling of the chambers of the profiles (partly encased profiles). The accepted loadings consist of an axial force and moments in both main directions, which can be applied at the top and/or the bottom of the column. The program calculates these columns according to EC 4, 4.8. For steel grades S420 and S460 the user can decide if the correction according to annex H shall be considered. The calculated columns are always double-symmetric and present the same section throughout the whole height oft the column.
ArcelorMittal COnnection Program COP2 version 1.05
Design of Composite beam-to-column Joints according to Eurocode (EN 1993-1-8 and EN1994-1-1).
Composite Floor Slabs - FRACOF version 0.14
This software designs composite floor slabs at elevated temperatures by taking into account the enhancing effects of the membrane action in slab. FRACOF also checks perimeter beams and provides a critical temperature for each of them.
ArcelorMittal AFCB version 3.08 : Composite Beam Fire Design
software to calculate the ultimate bending moments for composite beams at room temperature according to Eurocode 4 [1.1] (ENV 1994-1-1) and for the ISO fire classes R3O, R6O, R9O, Rl2O and R180 with accordance to the Eurocode 4 [1.2] (ENV 1994-1-2).
ArcelorMittal AFCC version 3.06 : Composite Column Fire Design
software to calculate the ultimate loads for composite columns AF 30/120 at room temperature according to Eurocode 4 [1.1] (ENV 1994-1-1) and for the ISO fire classes R3O, R6O, R9O and Rl2O, with accordance to the Eurocode 4 [1.2] (ENV 1994-1-2).
ArcelorMittal OZone version 2.2.6
software to evaluate the temperature development of the gases within a compartment during the course of a fire according to EN 1991-1-2 and corresponding steel temperature according to EN 1993-1-2
ArcelorMittal LUCA version 1.2
software accompanying a design guide for industrial halls in fire conditions. This tool calculates displacements and additional horizontal forces that appear in industrial halls during fire enabling the engineers to consider their effect in the design in order to avoid collapse or risk of human life.
ArcelorMittal AcoBri version 3.01
ArcelorMittal Composite Bridge is a preliminary design software for composite road-, railway- and footbridges.
INerd version 1.0.0 - Innovation in Earthquake Resistant Design
Software to avoid the collapse of buildings in seismic situation by simulate the inclusion of rebar - steel reinforcing bars - on the pillars of support (the mechanism of "Soft-Storey ¨).
Durability version 1.0.5.4 - Service Life Analysis for Sheet Piles
Service Life Analysis for Sheet Piles - Download here the new software for the Analysis of the Service Life of Sheet Piles!
Prosheet version 2.2: Sheet Pile design for cantilever and anchored wall systems
Preliminary Sheet Pile design software for cantilever and anchored wall systems according to the Blum theory. The ProSheet 2.2 integrates all the forces required for a preliminary design of a sheet piling structure.
CAD Downloads (DWG-Files) - Sheet piles
Dwg files are compatible with AutoCAD 2005 and above. Refer to the section headed "Delivery conditions" in the sheet piling catalogue for information on tolerances and maximum fabrication length.
CAD Downloads (DXF-Files) - Sheet piles
Refer to the section headed "Delivery conditions" in the sheet piling catalogue for information on tolerances and maximum fabrication length.
ACE SINGLE version 1.16.1
ArcelorMittal Cost Estimator Single: Cost and weight estimation for multi-storey buildings based on I-sections. Compares the different solutions available to four-column modules.
ACE Multi version 2.8.1
ArcelorMittal Cost Estimator Multi: Cost and weight estimation for multi-storey buildings based on I-sections. Analyses the various construction systems of a complete building
.
.
وللتنزيل يمكن الذهاب الى الروابط التالية
http://www.4shared.com/file/lwA-rjHn...KEYpart01.html
http://www.4shared.com/file/5RM2joVB...KEYpart02.html
http://www.4shared.com/file/BQ4W7UnO...KEYpart03.html
http://www.4shared.com/file/4zgHAb5p...KEYpart04.html
http://www.4shared.com/file/NKhPp6kD...KEYpart05.html
http://www.4shared.com/file/BKt6Znpw...KEYpart06.html
http://www.4shared.com/file/AglxjqM7...KEYpart07.html
http://www.4shared.com/file/x-HSmBBS...KEYpart08.html
او الذهاب الى الموقع الرسمي للشركة
http://www.arcelormittal.com/sections/
وللامانة فقد قمت باجابة بعض الاسالة التي طرحها بعض الاعضاء في مشاركات سابقة ومنذ فترة طويلة من نفس usb key الذي امدتني به الشركة الاصل.
وللعلم لم اقم بتنزيل كل usb key.
).
ارجو ان تفيدكم جميعا وخاصة مستعملي الكود الاوروبي... منقول | |
|
الرئيسية
